Last updated - November 26th, 2021
Access to clean water is something that should be taken into consideration throughout your home. While there are many different types of whole house filtration units on the market, we highly recommend taking a look at a Home Master system. This brand offers great, long-term solutions with each of its products.
Let’s take a look at their systems, complete with a comprehensive buying guide to help you make the best decision.
Main Features and Benefits
The whole house filtration system will provide you with a variety of features and benefits, and it will be worth every dollar you spend on it. Compared to filtered water pitchers and faucets, the whole house water filters offer many advantages.
Check the list below and see the most important among them:

- These systems will improve both the smell and taste of your water.
- There will be much less wastewater compared to faucets.
- Water will be cleaned at its entry point.
- Water is purified in the whole system, not just at the sink like this under the sink water filter.
- The system can remove up to 95% of all the iron, bad minerals, and similar contaminants.
- The filter is long-lasting, up to 10 times longer than the regular filters.
- The filtration process is much more powerful compared to pitchers and faucets.
4 Different Filter Cartridges
Home Master can have up to three filtration stages. It depends on the model you choose. It can effectively filter as well as 1 micron. Read more details about each of the four available cartridges:
- Multi-gradient Depth Polypropylene Sediment Filter has a lifespan between six and twelve months.
- Granular Activated Carbon has a lifespan of approximately 100,000 Gallons or twelve months.
- Granular Activated Catalytic Carbon with KDF85 has a lifespan of approximately 100,000 Gallons or twelve months.
- The Iron Reduction Filter will remove any iron usually found in the well water source.

Comparison Table








Home Master Filters – Expert Favorites
4. The Three Stage Water Filtration System


The Home Master HMF3SDGFEC Three Stage Water Filtration System is a high performing filtration system that can handle even the harsh contaminants present in well water. Just like the name suggests, it features 3 stages of filtration:
Stage 1:
The first filtration stage features a Multi-gradient Depth Polypropylene filter that:
- Is constructed with a 25-micron surface, 10-micron layer, a 5-micron layer, and a 1-micron core.
- Is constructed for the purity of bacteria and chemical stability.
- Offers triple the dirt-holding capacity of equivalent size cartridges.
- Has a lifespan of 6–12 months.
Stage 2:
After the first stage, the second stage offers more precise filtration by:
- utilizing a Radial Flow Iron Reduction Filter.
- utilizing Iron Filtration for the applications with a high-flow.
- offering Radial Flow architecture for reduction of iron with a low-pressure drop (less than one psi).
- reducing iron in water quickly and efficiently up to 3 ppm.
- * Note that the lifespan depends on the iron level in the water and other contaminated materials (check the image below).

Stage 3:
The final stage ensures optimal filtration through the following features:
- The radial release of granular activated carbon is around 20 microns.
- An extended life cycle of up to 100,000 gallons, removing odor, chemical materials, and chlorine.
- Ideal high-flow applications < 1 psi pressure drop @ 20 gallons per minute
- Radial Flow architecture offers an excellent reduction of iron with a low-pressure drop (less than one psi)
- Improved contact time for carbon to get the water purified as much as possible
- High-quality coconut shell carbon for the reduction of full chemical pollutants
3. Home Master HMF2SDGC 2-Stage Fine Sediment and Carbon Whole House Water Filter, White

Size | Massive in size: 28in x 18in x 9in |
Filtering capacity | With very powerful and strong water pressure, it can filter up to twenty gallons per minute. |
Type of filters | Four gradient sediment-replaceable density filters provide better filtering and better dirt retaining power. It can filter up to 1 micron |
Capacity | Over 100k gallons, meaning that you won’t have to replace the filter for an extended period of time. When the time comes, you can easily replace the carbon filter, but it shouldn’t be necessary for at least a year. |
Purification process | The Home Master system can remove up to 95 percent of the potentially harmful elements in the water. It’s capable of removing sediment, chlorine, and any chemicals the water contains. |
Warranty | 2-year |

The HMF2SDGC 2-Stage Whole House Filter is perfect for your water supply.
When choosing a water filter for your home you will want to test your water and know which metals it contains. In the case of sulfur problems, manganese, or iron, we assure you that this filter is the best product you can find. Plus, it will also give more power to the water pressure. This unit features two stages:
Stage 1:
- Multi-gradient Depth Polypropylene filter. Surface – 25 microns, 10-micron layer, the layer has 5 microns, and the core has 1 micron.
- Constructed for the purity of bacteria and chemical stability.
- Features 4 different layers of gradient density in order to improve the filter efficiency.
- Offers triple the dirt-holding capacity of equivalent size cartridges.
- Multi-gradient Depth Polypropylene Sediment Filter has a lifespan of 6–12 months.
Stage 2:
- Features a Radial Flow Iron Reduction Filter.
- Offers Iron Filtration for the applications with a high flow.
- Features Radial Flow architecture, offering an excellent reduction of iron with a low-pressure drop (less than one psi).
- Offers iron reduction.
- Has a lifespan of up to 12 months
2. Home Master HMF2SmgCC Two-Stage Filtration System

Size | Massive in size: 28in x 18in x 9in |
Filter housing | It has the most powerful water pressure and can reach up to 10 GPM. |
Type of filters | Four gradient sediment-replaceable density filters provide better filtering and better dirt retaining power. It can filter up to 1 micron |
Capacity | It has a capacity of around 95k gallons, meaning that you won’t have to replace the filter for an extended period of time. When the time comes, you can easily replace the carbon filter, but it shouldn’t be necessary for at least a year. |
Purification process | The Home Master system can remove up to 95 percent of the potentially harmful elements in the water. Capable of removing sediment, chlorine, and any chemicals the water contains. |
Warranty | 2-year |

The HMF2SmgCC Whole House Two-Stage Filtration System is perfect for the city water that contains chlorine or chloramines. In addition, it can also filter copper, mercury, lead, pesticides (if any), and other metals.
Its primary cause is to deliver a perfectly clean and purified water for every faucet and pipe in the house. It features two stages, each with a different filtration process to target different issues.
Stage 1:
- Multi-gradient Depth Polypropylene filter. Surface – 25 microns, 10-micron layer, the layer has 5 microns, and the core has 1 micron.
- Constructed for the purity of bacteria and chemical stability
- The water filter has 4 different layers of gradient density in order to improve efficiency
- Multi-gradient Depth Polypropylene Sediment Filter has a LifeSpan between six and twelve months
Stage 2:
- Radial Flow Iron Reduction Filter
- Iron Filtration for the applications with a high-flow
- Radial Flow architecture offers excellent reduction of iron with a low-pressure drop (less than one psi)
- Reduce iron in water quickly and efficiently
- It will reduce the risk of damages to pipes and water heater
1. Home Master – Single Stage Filter

Size | Massive in size: 25in x 9in |
Filter housing | It has the most powerful water pressure and can reach up to 20 GPM. |
Type of filters | Four-layer sediment filters will provide better filtering and better dirt retaining power. They can filter between 25 and 1 micron. |
Capacity | It has a capacity of around 95k gallons, meaning that you won’t have to replace the filter for an extended period of time. When the time comes, you can easily replace the carbon filter, but it shouldn’t be necessary for at least a year. |
Purification process | The Home Master system can remove up to 95 percent of the potentially harmful elements in the water. Capable of removing sediment, chlorine, and any chemicals the water contains. |
Warranty | 2-year |

And at the top of our list, we have the original variation. This Single Stage Carbon Filter is perfect for the city waters that contain chlorine or chloramines, copper, mercury, lead, pesticides
In just one stage, this filter will get the job done and is perfect for those looking for high quality filtration on a budget. If your home is not located in an area with severe pollution and contamination, this is a quick fix to get the same high-quality water as you would with multiple stages of filtration.
Stage 1:
- Multi-gradient Depth Polypropylene filter. Surface – 25 microns, 10-micron layer, the layer has 5 microns, and the core has 1 micron.
- Constructed for the purity of bacteria and chemical stability
- It has 4 different layers of gradient density in order to improve efficiency
- Multi-gradient Depth Polypropylene Sediment Filter has a LifeSpan between six and twelve months
Installation Manual
Things You Should Do Before Installation

- For well water, the very first thing you should do is apply chlorine to your pipes and well. It’s the necessary thing to do before you even remove the filters.
- Make sure to protect the unit and to keep it dry. In addition, steer clear from freezing temperatures or direct sunlight
- The next pre-step is making a list of the tools you need to fully install the filtration system
- Double-check if you turned the water supply off, before starting the installation process.
- Switch the electric power off to your electric heater until the installing process is complete. When the unit is assembled and compressed, switch on the water and don’t stop until all the air from the pipes is gone. After this procedure is complete, feel free to turn the power back on to the heating system.
- We suggest using the Teflon tape on thread fittings.
- Make sure to check the inlet and outlet signs. The sediment filtering stage is the very first step of the water filtration cycle.
- It would be good to install a 3-valve bypass and the loop.
- The copper pipe usually gave two models. Our recommendation is to use the thicker model instead of the thinner model.
Installation of Home Master System:
For Water In
Step 1: The primary valve for shut-off should be turned off.
Step 2: The next step is to open all plumbing fixtures in order to drain the water as much as you can.
Step 3: The next step is opening water installations and draining the water from the pipes and water fixtures in your home. It’s best to install the filter as close as you can to the primary water supply pipe.
Step 4: Carefully determine the place where your filter will be placed. Cut through the pipe. Make sure it’s in a dry, protected area.
Step 5: If you put the pressure gauge or a shut-off valve from both sides of the unit, it will be easier to use it afterward.
Step 6: Put the Master Water Filter in the pipe and make sure that the system is leveled.
Step 7: If the pipe needs adjustment, fit it in the section you cut.
Step 8: For extra support, the pipe hanger should be on the WATER inside. Below is a graph for your reference.

For Water Out
Step 9: Fit together the pipe union and shut off the valve. We suggest using the Teflon tape on thread fittings.
Step 10: The shut-off valve and the filter should be fitted at the same time. It’s best to use a pipe nipple to draw them together.
Step 11: Fit the unit and the switch-off valve together at the same time on the outside of the filter. Fit pipe union to switch off the valve on the outside.
Step 12: Make sure to check the length of the pipe/pipe union, because maybe you’ll need to add an extra one/s. If not, just join the pipe and the union pipe together.
Step 13: For extra support, the pipe hanger should be on the WATER Outside.
Step 14: Remove filters from packages
Step 15: Change the old filter in the sump with the new one. Take care that the slots are over the standpipe
Step 16: Apply supplied silicone grease and o-ring to the o-ring channel at the top of the sump
Step 17: Fit to housing cap hand-tighten, then fit snug with housing wrench.
More Features and Benefits
Filtering Performance
This home water filter has a huge filtering capacity. With mighty and strong water pressure, it can filter up to twenty gallons per minute.
Four gradient sediment-replaceable density filters provide better filtering and better dirt retaining power. It can filter up to 1 micron.
Water Pressure of These Units
The installation of the system is effortless and quick. The filter arrives in the package with all the important things you need. The maximum 1-inch diameter is there to ensure that the water’s pressure does not decrease while in use. The filter is big, which means a larger quantity to intercept and catch contaminants, mainly sediments. Because of this, it has a longer lifespan,
Removal of Sediments
Sediments could significantly impact the equipment, and it goes far beyond the look of your water. They can seal filters and dirty pipes, which are both troublesome and costly to maintain. The sediment filters that this brand produces blend into the water surface exactly where it reaches your house. It captures all the sediments before it could harm and go into the water system of your house. An unusually large filter ensures that a lot of sediments can be captured until it needs changing.
The Water Treatment
All Home Master systems can treat the following: chlorine, chloramine, iron, manganese, and the sulfur smell. It can also treat mercury, pesticides (if any), and some other metals
Changing Filters – Step-by-Step
In this part of the text, we will explain and give you step-by-step instructions on How to replace house water filters.
Step 1: Chlorine
For well water, the very first thing you should do is chlorine to your pipes and well. It’s the necessary thing to do before you even remove the filters.
Step 2: Turn Off the Water
The second step is to turn off the water that supplies the water system. The red button that does this is located at the top of the filtration housing cap. When you click it, the burden of the machine will be relieved. If your water supply system does not contain a relief valve, leave the water tap open. This will allow you to remove the filters.
Step 3: Unscrewing
Unscrewing the sump from the cap is an important part of the process. Use the filter wrench for removing the cartridge.
Step 4: Scrubbing
Use a sponge to scrub the cap and the sump with hot water. Add two spoons of bleach to the water for more efficient results.
Step 5: Pouring the Bleach
Add two spoons of bleach in the water for more efficient results in each empty sump. Close it and tight it, but make sure not to over-tighten it. Open a faucet as far as you can from the system and let the water run. Once you smell the chlorine, flush down the toilet. Repeat this action while moving closer to the main system.
Step 6: Lubricating
O-ring should be lubricated with clean silicone grease. The next thing you should do is put o-ring in the grove and tap it to set the level equally. If the o-ring has any damage or stretched, make sure to replace it.
Step 7: Placing the New Filter
Open a new filter package, take it out, and put it in the sump. Make sure that the cartridge slips over the standpipe at the bottom of the sump.
Step 8: Tightening
Fit to housing cap hand-tighten, then fit snug with housing wrench. Avoid making it too tight.
Step 9: Turn On the Water
Slowly start turning on the water, allowing the system to fill up with water. When the water is flowing, and the air is clear, make sure to close the system’s valves downstream. Check the whole system carefully, trying to find any leak. In case you find a leak, you should follow the depressurize procedure and check the o-ring. Once you check it, retighten.
Step 10: Run the Water Through the Pipes
Slowly start flushing the water through, allowing the system to run until it purges the air and carbon. After the installation, the water can be cloudy.
Switch the water back on as slow as you can. If you hear sounds of the water entering the system, don’t worry about it. It will stop in a few minutes. Once you mount the unit, you need to clear it as well. You can do this at the closest water faucet, but keep in mind that you must use COLD water. The water may have some shade of black color for a while. That’s normal as well, and it’s because of the carbon.
Keep running the water through it until it’s completely cleared. After you finish that step, switch the water off, please don’t do anything for a while, and then switch it again.
Filter LifeSpan and Replacement
The very important info is how long the filter lasts and when you consider buying this filtration system. Below is the proposed replacement plan, including all four filtering cartridges:
- Multi-gradient Depth Polypropylene Sediment Filter a LifeSpan between six and twelve months
- Granular Activated Carbon with a LifeSpan for around 100,000 Gallons or twelve months
- Granular Activated Catalytic Carbon with KDF85 with a LifeSpan for around 100,000 Gallons or twelve months
- For the Iron Reduction Filter, please check the image below:

Every Whole House system cartridge is made to last long and of good quality to endure poor water environments.
Pros and Cons
Frequently Asked Questions
How Is the Home Master a Better Solution Than the Other Water Systems?
Purifying. It can remove many chemical contaminants such as pesticides, chloramine, chlorine, and lead.
Eliminating leak. After around five years, the shells and membranes of the rivals canister housing filter start to degrade and rot. Eventually, they end up failing, possibly causing significant leakage. Customizable filters used in the Home Master brand are updated every year to fix this issue virtually. If you change them every year, it will always be a more hygienic system with clean water.
User-friendly. The important thing you’ll notice is that the filters are installed in the unit’s housing. Next year, when the date to change the filter finally comes, all you need to do is unplug it. You won’t even need a single tool for that!
What Contaminants Can the Home Master System Remove?
This unit can remove many contaminants. Most effectively, it can remove lead, nitrates, copper, chromium, and fluoride like the Home Master countertop filter.
How Many Gallons of Water Can the Home Master System Process Before I Must Change the Cartridges?
The main cartridge cycle is around 100,000 gallons and can last for about one year for the regular family. Sediment and metal filters could require a replacement a bit more frequently. It will depend on the concentration in the well you use.
Conclusion
Should you buy this water filter? Not everybody wants such an efficient and powerful home water purification system. However, if your chloramine-treated water tastes and smells as if it’s coming out of a pool, this filter will solve more than one issue. Perfect water technologies produce the Home Master water filtration system.
Users save hundreds of plastic bottles costs because this filter can be used for a very long time. And if the lead is leaking out of your pipes, you’ll know you shouldn’t drink it. Bottom line, this is probably one of the best water filters available. Everyone deserves clean water in their homes. We encourage you not to hesitate with this filter.